Products

• analog measurement of the input signal
• transducer for measurement DC current or voltage
• allows unipolar and bipolar input and output signal
• directly current measurements up to ±10A, voltage up to ±1000V DC
• conversion accuracy <0,1%
• response time 1ms
• dielectric strength input / output / supply power 4kV
• universal power supply 19 – 300V DC & 90 – 250V AC

• two-state programmable switch for monitoring of electrical values or temperature
• output relay with changeover contact
• Possibility of easy setting of switching value by potentiometer or programmed
• input only RTD, R
• supply voltage: 12V / 24V DC ± 25% without galvanic isolation
• DIN rail mounting
• the temperature adjusting element is inside the housing

• 1 measurement input
• three control outputs
• communication line
• simple program (2 x ramp-up, 2 x soak)
• possibility of delay in starting the program
• running a program using the keyboard
• simple operation

• analog measurement
• true RMS value of current or voltage
• signal processing with crest factor up 10
• frequency range 40 … 1000Hz
• conversion accuracy  0,5%
• response time 300ms
• isolation input-output-power supply: 4000Vef
• loop-powered

• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• for outdoor use, IP65, -50…+100°C

• converter without galvanic isolation
• transmitter with 4-20mA otput is designed for transduction:
     - voltage from any thermocouple with linearization and cold junction compensation
     - temperature from RTD or resistance from resistance transmitter
• easy programming by AX-USB adapter (AY-USB) without power supply
• power supply by output loop 11…30V DC, any polarity
• slim design, DIN 35 rail-mounted, width 12,5mm

• 4-20mA loop-powered
• rated impuls voltage Uni: 8kV
• analog measurement of the input signal
• transducer for measurement RMS value of AC current or voltage
• signal processing  with crest factor of 10
• frequency range 40 až 1000Hz
• accuracy <0,5%
• response time 300ms
• dielectric strenght  Ua input / output: 4kVrms
• clearances and creepage distances min. 8mm
• designed for DIN 35 rail mounting

• sada nejčastěji používaných pufrů 4,01 - 7,00 - 9,18 pH
• barvené provedení usnadní rozlišení při kalibraci
• 4,01 oranžový, 7,00 zelený, 9,18 modrý
• balení 100 ml PET lahve
• jmenovité hodnoty pH platí při +25°C
• roztoky jsou dodávány příslušnými certifikáty a bezpečnostními listy

Postup kalibrace najdete zde.

• stem from stainless steel diameter 5, 4 or 3mm, min. length 15mm
• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• temperature range -40…+200°C
• dielectric strength: 500V, insulation resistance min. 20MΩ (circuit to metal parts)

• 1 measuring inputs
• 3 outputs
• communication line
• ramp function 
• automatic / manual operation
• variable setting
• secondary controller in system "Master - Slave"
• secondary controller in cascde regulation

• one- range converter
• isolation standard unipolar and bipolar signals
• digital processing and transfer A/D and D/A
• response time: 1ms, for order up to 300ms
• accuracy 0,1%
• power supply 18VDC for loop-powered transmitter on input
• dielectric strength input / output / supply power 4kV
• auxiliary power supply in wide range 19 to 300VDC & 90 to 250VAC

• power supply 19..300VDC & 90..250VAC with galvanic separation 4kV
• measurements
  • RTD, Tc, R, U, I
  • unified signals 0-20mA, 4-20mA, 0-10V ....etc.
  • voltage or current DC
•  output 1x relay or analog output 0-20mA, 4-20mA, 0-10V
• 4 digit red LED
• design for DIN rail
• to display the measured value
• monitoring of exceeding the set value

• two-state programmable switch for monitoring of electrical values or temperature
• output relay with changeover contact
• Possibility of easy setting of switching value by potentiometer or programmed
• supply voltage 24V DC ± 10% with galvanic separation 3kV
• DIN rail mounting
• the temperature adjusting element is inside the housing

• transmitter is mounted in a connection head DIN "B" dimension or any box
• it converts temperature from Pt100, Pt1000 or Ni1000 sensor to digital otput RS485
• transmitter has auto-recognize for Pt100 or Pt1000 sensors
• we can set it for other input signals too
• communication by RS485 line with master device on baud rate 600..19200Bd

• it can be use Pt100/A, B, from two to four wire connection, double sensor, Pt1000, Ni1000, KTY, PTC, thermocouples…
• easy connecting by connector M12x1 EC-FS4-L/16
• for outdoor use, IP65, -50…+100°C

• converter without galvanic isolation
• transmitter with 0-10V otput is designed for transduction:
     - temperature from RTD or resistance from resistance transmitter
• easy programming by AX-USB adapter (AY-USB) without power supply
• power supply 12…30V DC
• slim design, DIN 35 rail-mounted, width 12,5mm

• current or voltage analog measurement
• rectifier method of measuring the mean value
• average value calibrated to RMS of sine wave
• frequency range 40 … 1000Hz
• conversion accuracy  0,5%
• response time 300ms
• isolation input-output:  4000Vef